F405 flight stack with ESC 60A 3-6s 4in1 30x30mm

 F405 30.5×30.5 FC flight controller

• MCU: STM32F405
• IMU (Gyro): ICM42688P
• USB port type: Type-C
• Barometer: BMP280
• OSD: BetaFlight OSD w/ AT7456E chip
• DJI Air Unit connection method: via 6-pin connector or soldering
• 6-pin DJI Connector: Supported. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire replacement required.
• Black box: 16M
• Input current sensor: Yes. For 50A ESC, set scale=180 and offset=0.
• Power consumption: 3S – 6S Lipo (via ESC 8-PIN connector)
• BEC:
  • 5V: 5 groups, total current load 3A
  • 9В: 3 groups, total current load 2.5A
  • 3.3V: 1 group，max. current 300mA
• ESC Outputs: M1 TO M4
• UART:
  • 6 ports (UART2 UART5, UART3),
  • UART6 (dedicated for SBUS),
  • UART4 (dedicated for ESC telemetry),
  • UART1 (dedicated for VTX data configuration)
• Sbs Debugging: via UART6 channel
• ESC Telemetry: UART R4(UART4)
• I2C: Supported. SDA and SCL Pad on the front side. Used for magnetometer.
• LED Pad: Supported. LED, 5V and GND pads on the bottom of the front panel. Used for the WS2812 LED controlled by the Betaflight firmware.
• Buzzer: Available，5V, BZ pads
• BOOT button: Yes
• Firmware support: BetaFlight(Default)
• Firmware Target: GEPRCF405
• Mounting scheme: 30.5×30.5mm (4mm hole diameter)
• Dimensions: 37x 37×6.6mm
• Weight: 7.5г

*Note (BOOT button. Usage options):
[А]. In case of firmware crash: Press and hold the BOOT button and turn on the FC at the same time to force the FC to enter DFU mode.
[Б]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom side. By default, press the BOOT button briefly to switch to the LED display mode. Press and hold the BOOT button to switch between the backlight modes. In the BF-LED mode, all LED1-LED4 strips will be controlled by the Betaflight firmware.

FLASH HOBBY BLS 50A 30.5×30.5 4-in-1 ESC speed controller

• Firmware: BLS 16.7
• Constant current: 50A*4
• Peak current: 60A (5 seconds)
• TVS protection: Yes
• External capacitor: 35V560uF Low ESR Capacitor (in package)
• ESC Protocol: DSHOT300/600
• Power consumption: 3-6S LiPo
• Output power: VBAT
• Current sensor support (scale = 180, offset = 0)
• ESC Telemetry: Not supported
• Mounting scheme: 30.5 x 30.5 mm (4 mm hole diameter)
• Dimensions: 42.3 x 37 x 6.2 mm
• Weight: 12г

Link to download the configurator: here

PACKAGE CONTENTS

• 1x Flight controller  F405 30.5×30.5 FC
• 1x BLS 60A 30.5×30.5 4-in-1 ESC speed controller
• 1x Set of mounting components